1.Size:100*117*151mm 2.Three phase in and output 3.2.2kw speed controller 4. Competitive price 5.Short delivery time
400v ac 3 phase input and output 2.2kw motor speed controller
Technical Specification
Control Characteristics | Control Mode | SPWM (Sinusoidal Pulse Width Modulation) control (V/F sensorless vector control) | ||
Freq. Setting Resolution | 0.1Hz | |||
Output Freq. Resolution | 0.1Hz | |||
Torque Characteristics | Including the auto-torque, auto-slip compensation, starting torque can be 150% at 5.0Hz | |||
Overload Endurance | 150% of rated current for 1 minute | |||
Skip Frequency | Three zones, settings range 0.1~400Hz | |||
Acc/Dec Time | 0.1~600s (Independent settings) | |||
V/F Curve | Arbitrary V/F curve setting | |||
Stall Prevention Threshold Frequency Setting | 20~200%, Setting of Rated Current | |||
DC Injection Braking | Operation frequency 0.01~60Hz, output 0~100% rated current, start time 0~5s, stop time 0~25s | |||
Braking Torque | Approx. 20% (up to 125% possible with option brake resistor or brake unit externally mounted) | |||
Operating Characteristics | Frequency Setting | External Signal | Potentiometer 5kΩ/0.5W 0~+10VDC, 4~20mA, interface RS485; Multi-function Inputs (7 steps, Jog, Up/Down) | |
Operation Setting Signal | Keypad | Set by RUN, STOP | ||
External Signal | S0~S5 can be combined to offer various modes of operation, RS485 serial interface (MODBUS) | |||
Multi-function input signal | Multi-step selection 0 to 7, Acc/Dec inhibit, two Acc/Dec switches, External Counter, Jog, PLC operation, External Base Block, auxiliary motor protection, auxiliary motor control is invalid, drive reset, UP/DOWN key settings | |||
Multi-function output signal | AC drive operating, frequency attained, zero speed, PLC operation, counter attained, over torque, base block, operation mode, fault indication, drive is ready, overheat alarm, emergency stop | |||
Analog output signal | Indicate output frequency, current, voltage, frequency command, speed, power factor output signal | |||
Alarm Output Contact | Drive is fault, the contact will be ON (One form C contact or 3 open collector outputs) | |||
Operation Functions | AVR, over-voltage, over-current stall prevention, 3 fault records, reverse inhibition, momentary power loss restart, DC injection braking, auto torque compensation, slip compensation, S-curve, auto tuning, adjustable carrier frequency, frequency limits, parameters reset, vector control, PID feedback control, external counter, PLC, MODBUS communication, abnormal reset, abnormal restart, digital frequency output, sleep/revival function, 1st/2nd frequency source selections | |||
Protection Functions | Over voltage, over current, under voltage, external fault, overload, contact protection, overheating, electronic thermal, ground fault | |||
Display Keypads | 6-key, 4-digit, 7-segment LED, 4 status LED, master frequency, output frequency, output current, custom units, parameter values for setup, review and faults, RUN, STOP, RESET, FWD/REV | |||
Built-in brake chopper | Built-in for all models | |||
Environment Condition | Protection threshold | IP20 | ||
Pollution Degree | 2 | |||
Installation location | Altitude 1000m or lower, keep from corrosive gasses, liquid and dust | |||
Ambient temperature | -10°C~50°C non-condensing and not frozen (-10°C~40°C for above 5.5KW) | |||
Storage/Transportation temperature | -20°C~60°C | |||
Ambient humidity | Below 90%RH (non-condensing) | |||
Vibration | 9.80665m2(1G) less than 20Hz; 5.88m/s2(0.6G) at 20 to 50Hz | |||
Approvals | ||||
Technical Features
1. Adopts 16 bit microprocessor, sine wave PWM control
2.Automatic torque ascension and automatic sliding compensation function
3.Output frequency 0.1-400 Hz
4.8 period of speed setting and 7 period can be running the program
5.Low noise, carrier frequency can from 1 kHz-15 kHz adjustment
6.Two paragraphs Acceleration and deceleration time and two segments of the curve slow
and deceleration
7.Simulation frequency set acceptable 0-10 VDC, 4-20 mA
8.The built-in serial communication interface RS-485 (baud rate can reach 38400)
9.Save energy running and automatic voltage stabilizing section function (AVR)
10.Adjustable V/F curve Acceleration and automatic and deceleration function
11.Simple vector control and built-in PID control, and the simple positioning function
12.Sleep/wake up function and zero velocity keep function
Technical Parameter
Single/three phase input, three phase output 220v±15% (hang machine) | |||
VFD Model | Adapter Motor (KW) | Rated Output Current (A) | Outer Size (mm) (L*W*H) |
SVF-M0.4S/T2B | 0.4 | 3 | 85*113*142 |
SVF-M0.75S/T2B | 0.75 | 6 | |
SVF-M1.5S/T2B | 1.5 | 8 | |
SVF-M2.2S/T2B | 2.2 | 11 | 100*117*151 |
SVF-M3.7S/T2B | 3.7 | 18 | 125*166*220 |
Three phase input/three phase output 380v±15% (hang machine) | |||
VFD Model | Adapter Motor (KW) | Rated Output Current (A) | Outer Size (mm) (L*W*H) |
SVF-M0.4T4B | 0.4 | 3 | 100*117*151 |
SVF-M0.75T4B | 0.75 | 4 | |
SVF-M1.5T4B | 1.5 | 5 | |
SVF-M2.2T4B | 2.2 | 6 | |
SVF-M3.7T4B | 3.7 | 9 | 125*166*220 |
SVF-M5.5T4B | 5.5 | 14 | |
SVF-M7.5T4B | 7.5 | 18 | |
Accessories
Factory View
Trade terms
a. Delivery term
We will delivery for you after you done the full payment within 3 to 15 working days
b. Payment
For small order by air or by express, it is 100% T/T in advance.
For large order by ocean, 30% deposit of the order value should be paid, 70% of the balance payment should be done before delivery
c. Packing
Unless otherwise stated in the offer, the prices include packing in accordance with CHINSC’S customary standard of packing.
Application
Textile, Chemical, Metallurgy, Mining, Pharmaceuticals, Ceramics, Paper, Oil, Plastics, Printing, Thermal power, Food and other fields.
Main Circuit Connection
Client Satisfaction
Reckoned to be the quality-oriented organization, we ensure that clients are served efficiently most
appropriate manner. Clients appreciate our range for their quality and easy availability, besides the
reasonable prices. Suggestions of clients are always welcomed and we make changes accordingly
if required. We ensure that queries of clients are solved in minimum time-frame with appropriate
solutions.
400v ac 3 phase input and output 2.2kw motor speed controller
