Automatic horizontal with the key machine can be equipped with flat-panel key, cross key, motorcycle key part of the car key, quasi-precision and reliable quality, the factory has more tune accurately, power-on you can use power supply: 220V new machine does not containlight bulbs, separately in the local purchase bulbs, fixture spacing 6CM.

Note:1,because this machine is the auto / manual integration of first use, remember that you want to machine the right edge of the black shaft pulled out one o'clock, this will switch to electric; itself black shaft inside one o'clock default manual mode, no power can be fitted with hand-cranked rocker (usually used, it is recommended not to install to get started cranks in order to avoid misuse).2,folder before the boot of a good key, be sure the fixture lifted a little and then boot to allow the tool to turn up and then slowly put down the fixture, so it will not because the keys stuck tool, leading to the motor can not turn and burn the motor. Like the motor of such misuse causes damage not covered under warranty.3,different batches produced by the appearance of colors and images is not the same, but the quality and performance, please rest assured.4,the use of electric state, please do not install the hand crank in order to avoid misuse; power outage need to use the manual hand-cranked, you must unplug the power outlet and cut off power to avoid sudden restoration of electricity and damage!

other related key cutting machine

Manufacturing qualitya) knife shaft and slide shaft parallelism be less than 0.25 mm;b) the knife Axial and radial runout should be less than 0.50 mm;c) blade shaft axial runout should be less than 0.25 mm;d) The guide pin and the tool level difference should be less than 0.40 mm;e) The guide pin with the tool longitudinal difference should be less than 0.10 mm;f) corner key fixture benchmark parallelism should be less than 0.015 mm.

Replication accuracya) the the toothed copy the key and model key elements of the position tolerance should be less than 0.10 mm;b) the toothed copy the key and model key elements of the radial depth error of less than 0.10 mm;c) to copy the key to open the lock of the model key wife should be smooth, and 100% successful.

Frequently Asked Questions: horizontal with the key machine and vertical with the key machine What is the difference, the two have to buy?

A: horizontal with the key machine and vertical with the key machine is completely different from the two machines.    Horizontal with the key machine with flat-panel key, cross key, the car class Key, with the horizontal with a spoon machine with zigzag-like keys are; such as our sales "solid edge", "cow" and "cross".    The vertical distribution of key machine with a computer key, is punching the security door keys, the keys of a one-pits on the surface; such as our sales, "Tak", "DMS" atoms ".    General two machines to be purchased, the two machines can be prepared most of the keys on the market. If your vote budget is relatively small, you can buy a horizontal plane and the horizontal plane can be formulated key, accounted for a large part of the market because the market "solid edge" and "cross" key.

transponder key programming machinekey code machineautomatic key cutting machine

The use of performanceProduction capacity: CopyOperation of the machine, the main bearing temperature rise should be less than 35 degrees Celsius.Electrical interface: three-pin socket 220 ± 10% (V), frequency of 50 ± 2% (Hz)Interchangeability: the machine tool axis should be able to easily replace the qualified tool.

Safety and environmental protectiona) where moving parts affect safety shall be provided with protective equipment and safety signs.b) part of the sealing leakage.c) when the normal use of the machine noise should be less than 50 db.

General requirementsThe products should comply with the requirements of this standard, and manufactured in accordance with prescribed procedures approved by the drawings and technical documents.

Environmental conditionsIn temperatures of -10 to 40 degrees Celsius, flat on a solid level surface should be able to work properly.

Appearance of the requirementsProduct modeling is required to meet the principles of beautiful, safe, comfortable and stylish.Polished smooth outer surface of the product, does not allow the presence of burrs. Hammer paint spray after full rust, uniform color, the film is flat, smooth and firm.

We have over 20 models of key cuting machine and prdouce almost 10, 000pcs key cutting machines every

year, and export to world wide including mid east, south america, europe and asia abd africa. Our

machine has the advantages of good quality, unique design and reasonable price. Welcome the inquiry of

customers from world wide.

automatic key cutting machinekey code machinekey copy machine

automatic key cutting machinekey code machinekey copy machine

automatic key cutting machinekey code machinekey copy machine

automatic key cutting machinekey code machinekey copy machine