Specification 1、Name： 1.3MP AHD Module 2、Model：RS-HD226-A0 series 3、Technical characteristics： 3.1、1/3 CMOS MN34210 image sensor, Output AHD 720P or Analog 960H, OSD menu supports 12 different languages; 3.2、With high definition 720P, Effective resolution is up to 1296*1032, no delay, no compression, low lost, real-time transmission; lower noise 3.3、With 2D/3D noise reduction, sens-up, D-WDR, support motion detection / privacy protection, defog 3.4、PAL/NTSC switch, Various mirror modes, day-night modes switched by OSD, built-in HOLD picture (freezing) function 3.5、1.5*3pin power connector, Output AHD 720P/960H（A/C short circuit to GND or OSD switch）； 3.7、Can add UTC function, power (600W) & video (2KV) dual lightning protection design 3.8、PCBA 32*38 dual border design, OSP antioxidant PCB. Transmission distance can be up to 500 meters.4、Product picture：5、Product parameters:Image Sensor 1/3 CMOS MN34210Resolution1280(H)*720(V)Signal systemPAL/NTSCEffective pixels1.3 M PixelsS/N Ratio≥55dBMinimum illumination0.01LUXBacklight compensation (BLC)AUTOAuto electronic shutter (AES)AUTO/ 1/50（1/60）-1/50,000secAuto white balance (AWB)AUTOIR input voltageDC 0V to 3V/8VOSD menu(12 language)English/ Simplified Chinese/Traditional Chinese /German /French/ Italian/ Spanish/ Polish/ Russian/ Portuguese/ Dutch/ TurkishVideo output AHD(720P)/CVBS/1.0Vp-p/75Ω Video record occupation1min≈32 MB（4mm LENS）Working voltageDC12V/60mA ±5mAWorking environment-20℃ --- 50℃6、 Product structure& wiring definition diagram：Term：CDS_INICR A/B：IR-CUT7、 Shortcut operation approaches of OSD function:： (1)Press the down button of OSD cable for 5 seconds, the module system will be switched from PAL to NTSC (the default is PAL); re-press the down button for 5 seconds, the system will be changed from NTSC to PAL. (2)Press the left button for 5 seconds, the video output will be switched from AHD to CVBS(the default output is AHD) (3)Press the right button for 5 seconds, the video output will be switched from CVBS to AHD.AHD/CVBS (A/C for short)switching usage instructions:There are 2 methods to switch AHD/CVBS, as below: (1) Press shortcut key(left key or right key) of OSD menu for 5 seconds to switch; (2)When【A/C】pin is short-circuit to【GND】for 2~3 seconds, loosen and then will trigger to switch output;(can connect external touch switch) (3) When the default system is PAL, it means both AHD and CVBS are PAL. If you change the system from PAL to NTSC manually, CVBS is still PAL, cannot change to NTSC synchronously; you have to return to factory and re-burning the process if you want to change system synchronously.8、UTC technique introduction: UTC means Up the Coax (UTC), transferring 2 kinds of signal via general coaxial cable. One is image signal, the other is control signal. Use coaxial cable to transfer video signal and control signal from cameras at the same time, Through the function; you can control the cameras by DVR with UTC function easily, including OSD menu parameter setting and so on.8.1 UTC function operation demo： （1）Use DVR UTC menu, click the middle Ensure button: （2）Start to adjust the module parameters via DVR UTC function:
