If you are planning to wholesale best cheap and high quality rtv heat resistance red silicone sealant China,Website:http://www.sepnasealant.com, or hot sale rtv heat resistance red silicone sealant in China from professional rtv heat resistance red silicone sealant manufacturers and suppliers and factory, please feel free to contact SEPNA, and welcome to check products price with us.PUNADE Silicone series with high temperature resistancePUNADE high temperature resistant silicone series are organic silicon bonding sealant. They are made of special silicon rubber material. ◆Detailed Product DescriptionFeatures1.Excellent resistance to extreme temperature between -60～315℃.2.Good adhesion, moisture, shock, corona, leakage of electricity and aging resistanceUsage:Bonding and sealing of the industrial products, eg. Steam irons, high temperature air filters, oven and pipes Note: 3103LL is very thin, 3103L is thin, 3103 is half-flowing, and 3106R is pasty fluid.Please take your attention when making the choice.◆Data TableTesting Term1103LL1103L11031106RBefore CuredPerformanceRed/FlowingRed/FlowingRed/half-flowingRed/pastyDensity（g/cm3，25℃）1.031.101.201.30Viscosity （cps）10001200050000pastyCuring Speed （min，25℃）10-1510-1510-1510-15Time of fully cured（hr，25℃）24242424Curing TypeOne component condensation ketone oxime typeFully CuredTensile Strength（MPa）0.71.01.82.5Elongation at break（%）250350300300Hardness（Shore A）20232735Tensile-shear strength（MPa）1.01.21.42.0Peel strength（N/mm）3.5557The linear shrinkage（%）0.50.50.50.5Temperature range(℃)-60～315-60～315-60～315-60～315Volume resistance (Ω·cm)3×10153×10153×10153×1015Dielectric strength (kV/mm)20202020Dielectric constant (1.2MHz)2.82.82.82.8Flame retardant grade∕∕∕∕Note：All data above is tested under special condition(7 days after fully cured in the environment of 25℃, 55%RH). Just for reference. Not suitable to any situation.◆Operation1.Cleaning: cleaning the surfaces that to be glued and coated, removing the rust, dust, greasy dirt and other foreign matter and substance.2.Gluing: cutting nozzle to the required angle, extruding the liquid cement to the cleaned surface and making it well-distributed, then folding and fixing the glued surfaces.3.Curing: placing the glued or sealed components in the air to make them cured naturally. Curing is a process that being cured from surface to the internal.The sealant will be cured at a depth of 4~6mm within 24 hours (at room temperature and 55% relative humidity), if the glue position is deeper, especially the parts that not easy to come into the air,the time that being completely cured will be longer, if the temperature is low, the curing time will also be extended.4.Before the handle or package of the sealed parts, waiting for longer time to keep the adhesion and integrityNote:1.Tightening and sealing preserve the leftover sealant after the operation. 2.Removing the cured cement at the sealing part that might happen during the preservation, it could be normally used again.◆Package and StoragePackage 310ml/cartridge, 25pcs/carton StorageB component should be keep in cool and ventilative place Shelf life: 12 months (25℃)Transport as non-dangerous Article.◆Safety Operation MaterialMSDS isn't included here. Please read TDS, MSDS and label carefully before operation.You can get MSDS from Sepuna or other distributors, or mail to service center [email protected], or call +86-400-882-1323.◆Product WarrantyAll product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advices we supply don't apply in any circumstances. Sepuna don't make assurance of any other applications outside the specification until Sepuna supply a special written guarantee. Sepuna is only responsible to replace or refund if this product is defective within the warranty period stated above. Sepuna makes it clear that will not be liable of any accidents.
